The short answer
SureBreeze AC Repair Service repairs gas furnaces and heat pumps in Livermore homes, from ignition failures and cold air to short-cycling and thermostat problems. We explain what we find before any work starts and give you a straight answer on repair versus replacement. Bay Area Air District rules don't require you to replace a working furnace, so repairing a sound system is still a valid choice.
When the furnace or heat pump quits on a cold Livermore night, you want a clear diagnosis and a fix that holds up. SureBreeze AC Repair Service repairs gas furnaces, heat pumps, and the ductwork and controls that go with them in homes across Livermore, about 13 miles northeast of our base in Fremont. We tell you what failed, what it takes to fix it, and whether repair still makes sense for your system, so you can decide without pressure.
Heating problems we see in Livermore homes
Livermore sits inland in the Tri-Valley, away from the Bay's moderating influence, so winter nights here often feel colder than they do closer to the water. Many heating systems sit unused through a long, hot summer and then run hard once the weather turns. That pattern tends to expose worn parts in the first cold weeks of the season.
Common calls include:
- Furnace won't ignite, or lights and then shuts off after a few seconds
- Blower runs but the air from the vents is cool
- Heat pump short-cycles, ices over, or seems stuck in defrost
- Thermostat isn't calling for heat or reads the wrong temperature
- A burning smell that doesn't fade after the first few cycles of the season
- Rooms far from the unit stay cold while others are fine
- Banging, squealing, or rattling when the system starts or runs
How a heating repair visit works
We start with the simple things that cause a surprising number of no-heat calls: thermostat settings and batteries, power to the unit, the gas supply, and the air filter. From there we test the furnace's startup sequence step by step, including the igniter, flame sensor, pressure and limit switches, inducer and blower motors, and any error codes on the control board.
For heat pumps, we check the outdoor unit, defrost controls, reversing valve, capacitors, and refrigerant-side performance. On gas furnaces we also look at the heat exchanger and venting, because a crack or blocked flue is a safety issue, not just a comfort problem.
Before we repair anything, we explain what we found in plain terms and what the fix involves. Many common repairs, such as a dirty flame sensor, a failed igniter, or a weak capacitor, can often be handled in one visit when the part is on the truck. Less common parts may need to be ordered.
Gas furnace safety comes first
If you smell gas, leave the house right away and call your gas utility or 911 from outside. Don't flip switches or try to relight the furnace. Once the utility has cleared the home, we can diagnose and repair the furnace.
If a carbon monoxide alarm sounds, get everyone outside and call for help. Also avoid repeatedly resetting a furnace that keeps locking out. The lockout is often the system protecting itself, and forcing it to run can make the problem worse.
Repair or replace? What current Bay Area rules mean
Under Bay Area Air District Rule 9-4, natural gas furnaces manufactured from 2029 must meet a zero-NOx emission standard. In practice, that points homeowners toward heat pumps when a furnace is replaced after that date. The rules do not require you to replace working equipment. They only come into play when an existing furnace fails or is replaced, so repairing a furnace that's in good shape is a reasonable choice.
If your furnace is older and the repairs keep adding up, it can be worth thinking ahead about a heat pump on your own schedule rather than during an emergency. Note that the federal Energy Efficient Home Improvement Credit (25C) only covered qualifying heat pumps placed in service before December 31, 2025, so it isn't available for new installations. Bay Area homeowners can check BayREN and their local clean energy provider for current heat pump incentives. Amounts and availability change by funding cycle, so we confirm the current offer before quoting it.
Before you call, and where else we work
A few quick checks can save you a visit: confirm the thermostat is set to Heat and has fresh batteries, check the breaker for the furnace or air handler, make sure the furnace's front panel is fully seated so its safety switch is closed, and replace a clogged filter. If the heat still won't come on, give us a call.
Along with Livermore, we repair heating systems in Pleasanton, Dublin, and San Ramon, as well as Union City and Milpitas closer to our Fremont base.
More services in Livermore
- AC Repair in Livermore
- Heat Pump Installation in Livermore
- AC Installation in Livermore
- Furnace Repair in Livermore

