Skip to content
Serving Fremont and nearby cities Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (213) 723-6751

Furnace Repair in Union City, CA

Serving Union City and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (213) 723-6751

The short answer

SureBreeze AC Repair Service repairs furnaces in Union City homes, including ignition failures, cold air from the vents, short cycling, and noisy blowers. We diagnose the cause, explain it before we start work, and test the system before we leave. Bay Area Air District rules won't force you to replace a furnace that still works.

Most Union City homes don't run the furnace hard for much of the year, so problems tend to show up all at once. On the first cool night of fall, the thermostat clicks and nothing happens, or the system runs but blows cool air. SureBreeze AC Repair Service repairs furnaces across Union City and the 94587 ZIP code from our base in Fremont, about 4 miles to the southeast. We find the actual fault, explain it in plain terms, and fix it so your home stays comfortable through the damp winter months.

Furnace problems we see in Union City homes

Many furnaces here sit unused for months and then get switched on when temperatures drop. Dust settles on burners and sensors, filters get forgotten, and small issues from last winter come back. That pattern leads to a familiar set of service calls:

  • The furnace won't ignite, or it lights and then shuts off after a few seconds. A dirty flame sensor or a failed igniter is a common cause.
  • The blower runs, but the air coming out of the vents is cool.
  • The system short cycles, turning on and off repeatedly without warming the house.
  • The burners or blower motor make banging, scraping, or squealing sounds.
  • Some rooms stay cold while others overheat.
  • The thermostat doesn't seem to control the furnace at all.
  • A burning smell lasts beyond the first few minutes of the season.

What happens during a furnace repair visit

We start with the symptoms you've noticed and any error code blinking on the control board. Then we check the system in order: thermostat signal, power and safety switches, ignition sequence, gas pressure, flame quality, venting, blower operation, and airflow through the filter and ducts.

Once we find the cause, we explain it and tell you what the repair involves before we do the work. Common fixes include:

Before we leave, we run the furnace through full heating cycles to confirm it lights, heats, and shuts down the way it should.

  • Cleaning or replacing a flame sensor
  • Replacing an igniter, pressure switch, inducer motor, blower capacitor, or control board
  • Fixing airflow problems caused by clogged filters or blocked returns

Should you repair or replace? What Bay Area rules mean for you

Some Union City homeowners worry that new air quality rules will force them to replace a working furnace. They won't. The Bay Area Air District's appliance rules don't require you to replace working equipment. They apply only when an existing furnace fails or is replaced.

The long-term picture is changing, though. Under the Air District's Rule 9-4, natural gas furnaces manufactured from 2029 onward must meet a zero-NOx emission standard. In practice, that points homeowners toward heat pumps when they replace a furnace after that date. If your furnace is in good shape, repairing it is usually the sensible choice. If it's older and needs a major part, compare the cost of that repair with planning a heat pump installation on your own timeline.

About incentives: the federal Energy Efficient Home Improvement Credit (25C) covered qualifying heat pumps placed in service before December 31, 2025. It isn't available for new installations now. You can check BayREN and your local clean energy provider for current heat pump and electrification incentives. Amounts and availability change with each funding cycle, so we confirm the current offer before we quote it.

Furnace warning signs that need attention right away

Some problems shouldn't wait for a scheduled visit. If you smell gas, leave the house first, then call your gas utility or 911 from outside. If a carbon monoxide alarm goes off, get everyone out and call 911. Once the home has been cleared as safe, turn the furnace off and call us for a repair if you notice any of these:

  • Soot or scorch marks around the furnace cabinet or vent pipe
  • A yellow, flickering burner flame instead of a steady blue one
  • Water pooling around a high-efficiency furnace
  • A breaker that trips every time the furnace starts

Serving Union City and nearby communities

Union City is a short drive from our Fremont base, and we serve homes throughout 94587 in Alameda County. We also repair furnaces in Hayward, Newark, Pleasanton, Dublin, and Menlo Park. When you contact us, tell us what the furnace is doing, roughly how old it is, and whether it's a standard or high-efficiency model. That helps us bring the right parts and get your heat back sooner.

More services in Union City

Related

What to expect

How a visit goes

  1. Diagnosis comes first

    We test and inspect the system to find the actual cause before suggesting parts or replacement, so you aren't paying to guess.

  2. Options you can compare

    When a system could be repaired or replaced, we lay out both paths, what each involves and the tradeoffs, so you can decide with the full picture.

  3. Straight answers on rules and incentives

    We explain how local air district rules and current rebate programs apply to your home, and we confirm current incentive details before quoting them.

FAQ

Common questions

Why is my furnace blowing cold air?

Common causes are a dirty flame sensor, a failed igniter, or a clogged filter that makes the furnace overheat and shut off its burners while the fan keeps running. Also check that the thermostat fan is set to "auto" rather than "on." If the air still isn't warm, call us to diagnose it.

Do I have to replace my gas furnace because of the Bay Area Air District rules?

No. The Air District's appliance rules don't require replacing working equipment. They apply only when an existing furnace fails or is replaced. Under Rule 9-4, gas furnaces manufactured from 2029 onward must meet a zero-NOx standard, which matters mainly when you replace your furnace after that date.

Is it worth repairing an older furnace?

It depends on the furnace's overall condition and the part that failed. A sensor, igniter, or capacitor repair often makes sense even on an older unit. If an aging furnace needs a major component, we'll lay out the repair alongside replacement options, including heat pumps, so you can decide.

How often should I change my furnace filter?

Check it monthly during the heating season and replace it on the schedule the filter manufacturer recommends. A clogged filter is one of the most common reasons furnaces short cycle or shut down.

Are there incentives if I switch to a heat pump instead of repairing my furnace?

The federal 25C credit isn't available for heat pumps installed after December 31, 2025. You can check BayREN and your local clean energy provider for current incentives. Offers change with each funding cycle, so we confirm what's available before we quote it.

Do you serve all of Union City?

Yes. We repair furnaces throughout Union City's 94587 ZIP code, about 4 miles from our Fremont base. We also serve Hayward, Newark, Pleasanton, Dublin, and Menlo Park.

Need heating or cooling help in Fremont?

Tell us what your system is doing and we'll schedule a visit to diagnose it. You'll get a clear explanation of the problem and your options before any work begins.

Call (213) 723-6751 Request Service